brake sensor RENAULT SCENIC 2007 J84 / 2.G Anti Lock Braking System Bosch 8.0 ESP Workshop Manual

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 11V2 MR-372-J84-38C050$248_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12ANTI-LOCK BRAKING SYSTEM
REPLACING THE COMPUTER
When replacing the computer/pump assembly, follow this procedure:
–switch off the ignition,
–replace the computer (see MR 364 Mechanical or MR 370 Mechanical, 38C, Anti-lock braking system,
Hydraulic unit),
–enter the VIN using command VP001,
–configure the tachometric index using command VP007,
–configure the vehicle parameters with command VP004.
If Vdiag 0B, 11 or 12:
–configure the vehicle speed at initialisation with command VP032,
–inhibit or authorise the automatic brake light illumination (depending on the country's legislation)
using commands VP021 "Inhibit automatic brake light illumination" or VP022 "Authorise automatic
brake light illumination",
–enter the most recent After Sales operation date using command VP006,
–perform a road test followed by a fault reading to confirm that the system is operating correctly.
REPLACING THE COMBINED SENSOR
When replacing the combined sensor, you must erase the programming of the ESP sensors with command RZ003 (if
available).
Command RZ003 "Programming ESP sensors" is only available on Vdiag 09, 0A, 0B, 11, 12. IMPORTANT
It is imperative to check that the parameters selected match the vehicle's description.
Note:
Run this command every time the electric power steering is removed and refitted, and each time the steering wheel
angle is calibrated in the electric power steering subgroup.
MR-372-J84-38C050$248_eng.mif

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 14V2 MR-372-J84-38C050$372_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12ANTI-LOCK BRAKING SYSTEM
Tool faultAssociated
DTCDiagnostic tool title
DF001 50CCComputer supply
DF006 501FFront left-hand wheel speed sensor circuit
DF007 503FRear left-hand wheel speed sensor circuit
DF017 50C3Computer
DF020 50C3Tachometric index programming
DF026 500FFront right-hand wheel speed sensor circuit
DF027 502FRear right-hand wheel speed sensor circuit
DF055 50C3Vehicle parameter programming
DF063 5046Wheel speed inconsistency
DF066 5180No injection multiplex signal
DF090 5041Front right-hand wheel target
DF091 5042Front left-hand wheel target
DF092 5043Rear right-hand wheel target
DF093 5044Rear left-hand wheel target
DF097 5188No automatic transmission multiplex signal
DF126 50F4Combined sensor signal plausibility
DF152 50E6Multiplex network
DF153 50C3Multiplex network
DF186 5182No instrument panel multiplex signal
DF187 50CEBrake light activation relay circuit
DF188 50C6Brake light switch circuit
DF189 50F4Combined sensor circuit
DF190 50F4Combined sensor
DF191 50C9ESP on/off button circuit
DF193 5180Invalid injection multiplex signals
DF194 5158Invalid electric power steering signals
DF195 5188Invalid automatic gearbox multiplex signals
DF196 5158No power-assisted steering multiplex signal
MR-372-J84-38C050$372_eng.mif

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 50V2 MR-372-J84-38C050$496_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12
DF188
PRESENT
OR
STOREDBRAKE LIGHT SWITCH CIRCUIT
1.DEF : inconsistency
2.DEF : permanent high signal
NOTESSpecial notes:
1.DEF: This code means that the computer does not detect that the pedal is pressed
during braking (pedal pressed in relation to the pressure sensor).
2.DEF: This code means that the computer detects the pedal as pressed all the time
or that the brake light bulbs are the wrong ones.
Conditions for applying the fault finding procedure to stored faults:
Clear the stored fault, carry out a road test at a speed of > 36 mph (60 km/h) and test
the brakes with ABS regulation.
Using the diagnostic tool, check on the statuses screen that ET017 Brake pedal recognises the correct pressed
and released positions of the brake pedal.
If the correct pedal position is not displayed, use the interpretation of ET017 Brake pedal.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_DF188 /ESPBOSCH_V09_DF188/ESPBOSCH_V0A_DF188/
ESPBOSCH_V0B_DF188 /ESPBOSCH_V11_DF188/ESPBOSCH_V12_DF188

ANTI-LOCK BRAKING SYSTEM
BOSCH 8.0 ESP Vdiag No.: 08, 09, 0A, 0B, 11, 1238C
38C - 62V2 MR-372-J84-38C050$744_eng.mif
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12ANTI-LOCK BRAKING SYSTEM
STATUSES
CLEARING
Control
*csv: ET017: Brake pedal.
This status gives the position (depressed or released) of the brake pedal
ET023: ESP On/Off button
This status is used to check the ESP On/Off button operation. This status (pressed or released) is
checked by keeping the button pressed.
ET030: Automatic brake light illumination.
This status indicates whether automatic brake lighting is authorised or inhibited during CSV
(understeer control)*. The parameters of this status can be modified using commands VP021 and
VP022 according to the legislation in force in the country concerned.
RZ001: Fault memory.
This command is used for clearing the computer's stored faults.
RZ003: ESP sensor programming (Vdiag 09, 0A, 0B, 12 and 11).
This command resets the ESP sensor programming. Run this command every time work on the
electric power steering required programming of the steering wheel angle or after any operation on
the axle assemblies. Use this command when the combined sensor has been removed or replaced.
AC003:
AC004:
AC005:
AC006:Front left-hand wheel solenoid valves.
Front right-hand wheel solenoid valves.
Rear left-hand wheel solenoid valves.
Rear right-hand wheel solenoid valves.
These commands permit a check on the hydraulics of each wheel.
Raise the vehicle in order to be able to rotate the wheels, and check that they rotate freely.
Keep the brake pedal depressed to prevent the wheel being tested from being turned by hand
(do not brake so firmly that full braking power is reached).
Select and confirm the command for the wheel concerned (e.g. Front left-hand wheel solenoid valve,
etc.)
Turn the wheel concerned by hand; you should see it go through 5 locking/unlocking cycles.
AC013:Test wheel speed sensor feed (Vdiag 0A, 0B, 12 and 11).
This command is used to check that voltage pulses of approximately 12 V are detected by a
multimeter at the sensor connector terminals on the computer side. You must use command AC013
once only.
AC016:Pump motor test.
This command is used to test the pump motor control circuit. Select command AC016 Pump Motor
Test. The motor must run for 5 seconds.
AC187:Brake light on relay.
This command is for testing brake light activation by the ESP when controlling understeer during sharp
deceleration.
MR-372-J84-38C050$744_eng.mif

38C-70
MR-372-J84-38C050$930_eng.mif
V2
ANTI-LOCK BRAKING SYSTEM
Diagnostic - Fault finding chart38C
ALP 2 Locking of one or more wheels
NOTESOnly consult this customer complaint after a complete check with the diagnostic tool.
Reminder: wheel lock on a vehicle equipped with ABS, or tyre squealing perceived by the customer as locking,
may be part of the normal operation of the system and should not be automatically considered as faults:
–Braking with ABS on very poor roads (significant squealing).
However, if the wheels are actually locking, raise the vehicle in order to be able to turn the wheels and check:
–Possible inversion when connecting the speed sensors.
Using parameters PR001, PR002, PR003 and PR004, rotate the wheels slowly and check the consistency of the
results obtained.
If the value measured is zero, rotate the other wheels to confirm an electrical inversion of the sensors and repair
the wiring harness.
–Possible inversion of pipes on the hydraulic unit.
Use commands AC003 Front left-hand wheel solenoid valves, AC004 Front right-hand wheel solenoid
valves, AC005 Rear left-hand wheel solenoid valves and AC006 Rear right-hand wheel solenoid valves
while depressing the brake pedal and check for the occurrence of 5 locking/unlocking cycles on the wheel
concerned (see Dealing with commands). If the 5 cycles do not occur on the wheel tested (wheel remains
locked), check whether they occur on another wheel to confirm transposed pipes.
If the 5 cycles are not detected on a wheel and the pipes have not been subject to inversion, replace the hydraulic
unit.
Check that the sensor casing is secured when rotating.
Check the quality of the mounting of the wheel speed sensor (correct clipping without excessive play).
Check the conformity of the targets using special command SC001 "Check target teeth": condition, number of
teeth = 48.
If the fault is still present after these checks, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_ALP02 /ESPBOSCH_V09_ALP02/ESPBOSCH_V0A_ALP02/
ESPBOSCH_V0B_ALP02 /ESPBOSCH_V11_ALP02/ESPBOSCH_V12_ALP02BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12

38C-71
MR-372-J84-38C050$930_eng.mif
V2
ANTI-LOCK BRAKING SYSTEM
Diagnostic - Fault finding chart38C
ALP 3 Pull
NOTESOnly consult this customer complaint after a complete check with the diagnostic tool.
Disconnect one wheel speed sensor. Start the
engine and check that only the ABS fault warning
light comes on. Do not drive the vehicle if the brake
fault warning light is also lit, as the brake limiter
function is no longer guaranteed to operate
correctly. Carry out a road test with the ABS
deactivated.
Is the fault still present under these conditions?
no
Raise the vehicle so that you can rotate the wheels
and check:
–Possible inversion when connecting the speed
sensors.
–Possible inversion of pipes on the hydraulic unit.
To carry out these two tests, refer to and follow the
procedures given in ALP 2.
Check the condition of the ABS targets and that they
conform to specifications.
Also check the sensor/target air gap over one
revolution of each front and rear wheel.
If the fault is still present, contact the Techline.
yesIf the brake pedal travel is relatively long,
bleed the brake circuit.
If the travel is normal, check the tyre
pressures, the front axle, or for any leaks
in the circuit.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_ALP03 /ESPBOSCH_V09_ALP03/ESPBOSCH_V0A_ALP03/
ESPBOSCH_V0B_ALP03 /ESPBOSCH_V11_ALP03/ESPBOSCH_V12_ALP03BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12

38C-72
MR-372-J84-38C050$930_eng.mif
V2
ANTI-LOCK BRAKING SYSTEM
Diagnostic - Fault finding chart38C
ALP 4 Drift
NOTESOnly consult this customer complaint after a complete check with the diagnostic tool.
Disconnect one wheel speed sensor. Start the
engine and check that only the ABS fault warning
light comes on. Do not drive the vehicle if the brake
fault warning light is also lit, as the brake limiter
function is no longer guaranteed to operate
correctly. Carry out a road test with the ABS
deactivated.
Is the fault still present under these conditions?
no
Normal behaviour linked to the system operation
during the regulation phase, mainly on surfaces with
uneven grip or which are poorly laid.
yesRoad handling fault not connected with
the ABS.
Check the condition of the brake linings
and that they are to specification and
check the tyre pressures, the front axle,
etc.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_ALP04 /ESPBOSCH_V09_ALP04/ESPBOSCH_V0A_ALP04/
ESPBOSCH_V0B_ALP04 /ESPBOSCH_V11_ALP04/ESPBOSCH_V12_ALP04
BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12

38C-73
MR-372-J84-38C050$930_eng.mif
V2
ANTI-LOCK BRAKING SYSTEM
Diagnostic - Fault finding chart38C
ALP 5Unexpected ABS operation at low speed and with slight
pedal pressure
NOTESOnly consult this customer complaint after a complete check with the diagnostic tool.
Important: ABS regulation may be unresponsive when the vehicle is driven on surfaces
such as icy roads, cobbled streets, etc.
It is possible to feel brake pedal vibrations which are associated with the reaction of the system in particular
circumstances, such as:
–crossing rumble strips,
–tight cornering with lifting of the inside rear wheel.
These vibrations may be linked to simple brake limiter activation, when the pressure on the rear axle is limited.
If the fault is different, check the speed sensor connectors (micro-breaks) as well as the air gaps.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_ALP05 /ESPBOSCH_V09_ALP05/ESPBOSCH_V0A_ALP05/
ESPBOSCH_V0B_ALP05 /ESPBOSCH_V11_ALP05/ESPBOSCH_V12_ALP05BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12

38C-83
MR-372-J84-38C050$930_eng.mif
V2
ANTI-LOCK BRAKING SYSTEM
Diagnostic - Fault finding chart38C
*ASR: Traction control
ALP15ESP warning light comes on with the "ASR* disconnected or off"
message when the current is switched on without pressing the
ESP disconnection button
NOTESConsult this customer complaint only if the "Service", "ABS" and "Brake" warning lights
are not lit.
After disconnecting the battery, it is probable that the electric power steering loses the steering wheel angle
sensor indexing (the electric power steering no longer sends the steering wheel angle signal to the ESP, which is
then disabled).
The ESP system is not faulty, no fault is present in the fault memory, the ESP warning light comes on and the
"ASR disconnected or off" message indicate this transient and reversible status.
To restore the electric power steering indexing and enable the ESP again, it is necessary to:
–switch on the ignition or start the engine (to obtain maximum steering assistance),
–turn the steering wheel slowly to full right lock, to full left lock, then return slowly to the centre point after going
slightly past it,
–the ESP warning light should go out and the message "ASR disconnected or off" should disappear,
–stop the engine and switch off the ignition,
–switch on the ignition, start the engine and see that the warning light no longer lights up.
If the warning light and the message reappear, start the procedure described above again.
If the operation fails again or if this customer complaint appears without the battery having been disconnected, run
fault finding on the electric power steering and repair accordingly.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ESPBOSCH_V08_ALP15 /ESPBOSCH_V09_ALP15/ESPBOSCH_V0A_ALP15/
ESPBOSCH_V0B_ALP15 /ESPBOSCH_V11_ALP15/ESPBOSCH_V12_ALP15BOSCH 8.0 ESP
Vdiag No.: 08, 09, 0A,
0B, 11, 12